![]() |
![]() | ||
![]() | |||
|
PCChost 1100Frequently Asked Questions
The PCChost 1000 is based on Texas Instruments PCI-1130 CardBus controller while the PCChost 1100 is based on the PCI-1131. The PCI-1131 is an improved version of the PCI-1130. Other than the chip differences, the boards are identical. The PCChost 1000 is no longer available. Back to top
Yes, the PCChost 1000/1100 supports both 5V and 3.3V 16-bit PC Cards. Back to top
Windows NT 4.0 does not directly support the PCI-1130/1131 chip. However, Unicore offers CardWorks 6.0 for Windows NT 4.0 that supports CardBus and 16-bit PC Card. Cardware 6.0 may be purchased from Unicore Software at http://www.unicore.com/products/cardware/cardwarent.cfm. Refer to the PCChost 1100 Windows NT Application Note for installation help. Back to top
No. Because of the large number of systems and configuration differences in OS, BIOS, and system resources it is difficult for us to maintain an up to date list of systems. Back to top
Yes, Windows 98 directly supports the TI PCI-1130 and PCI-1131 used on the PCChost 1000/1100. Back to top
Windows 95 versions starting with the OSR2 release directly support the PCI-1130 and PCI-1131 CardBus controllers. Back to top
Go to the Control Panel and select System Devices. The Windows version is located on the "General" Tab. Under "Microsoft Windows 95" there is a number. 4.00.950 or 4.00.950A are the older releases of Windows. 4.00.950b is the designation for OSR2. Back to top
No, there is no plan to offer an upgrade. Back to top
Sycard offers a fixed price repair service to replace damaged connectors. The price is $85.00. Back to top
No. Neither the TI PCI-1130 or PCI-1131 chips are ACPI compliant. Back to top
Yes, the PCI1130 and PCI1131 used in the PCChost 1000/1100 support zoomed video. The user will need to construct a cable to go between the PCChost's probe points and a Zoomed Video ready video card. Back to top
Windows requires the use of ISA-compatible interrupts for 16-bit PC Cards. PCI interrupts are required for CardBus PC Cards. Back to top
Your status change interrupts are not configured correctly. The CardBus controller issues a hardware interrupt on card insertion and removal. On initial bootup, if there is a card inserted, the PC Card driver will issue a simulated hardware interrupt to configure the card. Back to top
Check the Device Manager - System Devices - PCI Bus - IRQ Steering and insure that the "Use IRQ Steering" and "Get IRQ Table from PCIBIOS 2.1 call" are checked. If not, select them and reboot the system. Back to top
Most installation problems are related to the system BIOS. Unfortunately, other than a BIOS upgrades, there is little that can be done. If the problem persists, try another system. The requirements for the system BIOS can be found on the Microsoft Web site at http://www.microsoft.com/hwdev/busbios/cardbus1.html and http://www.microsoft.com/hwdev/busbios/pccardwp.html Back to top
No. However, Texas Instruments can supply a debug program called PCIBUS.EXE that is designed to directly access the registers on the PCI-1130 and PCI-1131 chip. Contact TI directly for information. Back to top
Developing a driver requires a Driver Development kit (DDK). Microsoft supports driver development for all of their OSs through these DDKs. DDKs are also available from third party vendors. Vireo Software www.vireo.com or Blue Water Systems www.bluewatersystems.com. Back
to top Back to PCChost
1100 page.
| ||